SE

Question 1
Which one of the following assertions concerning code inspection and code walkthrough is true?
A
Code inspection is carried out once the code has been unit tested
B
Code inspection and code walkthrough are synonyms
C
Adherence to coding standards is checked during code inspection
D
Code walkthrough is usually carried out by an independent test team
       Software-Engineering       SE       GATE 2015 -(Set-2)
Question 1 Explanation: 
Note: Out of syllabus.
Question 2

A
612.06
B
612.07
C
612.08
D
612.09
       Software-Engineering       SE       GATE 2015(Set-03)
Question 2 Explanation: 
Note: Out of Syllabus.
Question 3
Consider a software program that is artificially seeded with 100 faults. While testing this program, 159 faults are detected, out of which 75 faults are from those artificially seeded faults. Assuming that both are and seeded faults are of same nature and have same distribution, the estimated number of undetected real fault is _____ .
A
175
B
176
C
177
D
178
       Software-Engineering       SE       GATE 2015(Set-03)
Question 3 Explanation: 
Note: Out of Syllabus.
Question 4
A
1-a, 2-b, 3-c, 4-d
B
1-d, 2-a, 3-b, 4-c
C
1-d, 2-b, 3-a, 4-c
D
1-c, 2-a, 3-b, 4-d
       Software-Engineering       SE       GATE 2014(Set-01)
Question 4 Explanation: 
Note: Out of syllabus.
Question 5
Which one of the following is TRUE?
A
The requirements document also describes how the requirements that are listed in the document are implemented efficiently.
B
Consistency and completeness of functional requirements are always achieved in practice.
C
Prototyping is a method of requirements validation.
D
Requirements review is carried out to find the errors in system design.
       Software-Engineering       SE       Gate 2014 Set -02
Question 5 Explanation: 
Note: Out of syllabus.
Question 6
In the context of modular software design, which one of the following combinations is desirable?
A
High cohesion and high coupling
B
High cohesion and low coupling
C
Low cohesion and high coupling
D
Low cohesion and low coupling
       Software-Engineering       SE       Gate 2014 Set -03
Question 6 Explanation: 
Note: Out of syllabus
Cohesion is a measure of internal strength within a module, whereas coupling is a measure of inter dependency among the modules. So in the context of modular software design there should be high cohesion and low coupling.
Question 7
                                                 
A
P-1, Q-2, R-3, S-4
B
P-3, Q-4, R-2, S-1
C
P-3, Q-1, R-4, S-2
D
P-4, Q-3, R-2, S-1
       Software-Engineering       SE       Gate 2013
Question 7 Explanation: 
Note: Out of syllabus [Web Technologies].
Question 8
A
There is no change.
B
Average cohesion goes up but coupling is reduced.
C
Average cohesion goes down and coupling also reduces.
D
Average cohesion and coupling increase.
       Software-Engineering       SE       Gate 2013
Question 8 Explanation: 
Note: Software Engineering is not a part of GATE syllabus now.
Question 9
 
A
p1 invokes p2, p2 invokes either p3, or p4, or p5
B
p2 invokes p1, and then invokes p3, or p4, or p5
C
A new module Tc is defined to control the transaction flow. This module Tc first invokes p1 and then invokes p2, p2 in turn invokes p3, or p4, or p5
D
A new module Tc is defined to control the transaction flow. This module Tc invokes p2, p2 invokes p1, and then invokes p3, or p4, or p5
       Software-Engineering       SE       Gate 2005-IT
Question 9 Explanation: 
Note: Out of syllabus.
There are 9 questions to complete.